🧭 From concept to mass production · Real LabVIEW + NI PXIe tests · Institutional memory

Hardware engineering that is never lost, never guessed and always documented

A complete system: it starts with the concept and ends with a certified product, ready for mass production. Every stage is calculated, simulated and tested on real hardware with LabVIEW and NI PXIe — and everything your team learns is kept.

The complete cycle

From concept to certified product, ready for mass production

Every stage of a hardware project in one system, with real analyses and tests — no jumping between tools, teams and suppliers.

Concept & requirements

The idea becomes technical specifications: voltages, currents, environment, applicable standards and target cost. We read your documents, sketches and datasheets.

Architecture & calculation

Choice of topology and sizing of every component, with a step-by-step calculation record.

Schematic & simulation

SPICE simulation on several engines, Monte Carlo tolerances, parasitics, thermal and EMI before any board exists.

PCB & mechanics

Layout in Altium Designer, enclosure and production drawings in SolidWorks — electronics and mechanics fit first time.

Prototype

Verified manufacturing pack (Gerbers, BOM, Pick&Place), board assembly and a 3D-printed enclosure.

Real bench tests

Automated tests with LabVIEW and NI PXIe hardware: real-time signal acquisition, efficiency, ripple, temperature and transients, measured and compared with the simulation.

Pre-compliance & certification

EMC and safety pre-compliance tests, a complete technical file and support during testing at the accredited lab until certification (CE and other markets).

Industrialisation & mass production

Design for manufacturing (DFM), a BOM without supply risks, production documentation and end-of-line tests with LabVIEW and NI for every unit made.

Real bench measurements flow back into the system: every tested project makes the next one faster and safer.

Real tests, not just simulation

LabVIEW + NI PXIe on the bench

Automated tests with LabVIEW and NI PXIe hardware: real-time signal acquisition, efficiency, ripple, temperature and transients, measured and compared with the simulation.

  • NI PXIe-8862 controller with LabVIEW Real-Time and analog and digital acquisition
  • Hardware-in-the-loop tests with deterministic processing
  • Measurement compared with simulation, point by point
  • LabVIEW supervisory screen with live results
  • End-of-line tests for series production
The usual problems

Three hardware-engineering problems — and how we solve them

Institutional memory

When an engineer leaves, the knowledge stays

Our agents learn from your company's experience and pass it on to whoever joins next.

Learns from your documents

Datasheets, application notes, internal standards, past projects and lessons learned become part of the agents' knowledge.

Keeps every decision

Every project, every correction made by your engineers and the reason behind each choice are recorded and versioned — nothing depends on one person's memory.

Improves with feedback

When an engineer corrects or approves a result, the agents learn from it. The team's experience builds up from project to project.

Answers newcomers

A new engineer asks «why did we use this inductor in this converter?» and gets the answer with the calculations and documents from back then.

Knowledge is private to each company and hosted in the EU (GDPR).

Engineering calculations

Every value has a formula, a substitution and a result

No values «from memory»: every component is sized with classical engineering formulas, with safety margins, and then confirmed by SPICE simulation.

Voltages and currents — average, RMS and peak
Switching frequency and duty cycle
Voltage and current ripple
Minimum inductance and capacitance
Magnetics: air gap, flux, core and copper losses
Conduction and switching losses, efficiency
MOSFET and diode voltage margins
Controlled impedance and PCB stack-up
Control stability: crossover and RHPZ
Thermal and EMI
Component tolerances (Monte Carlo)
Cross-validation by SPICE simulation

Example: buck converter 12 V → 5 V, 2 A, 200 kHz

Duty cycle D = Vout / Vin = 5 / 12 0,417
Current ripple (30 %) ΔIL = 0,3 · Iout = 0,3 · 2 A 0,60 A
Minimum inductance L ≥ (Vin − Vout) · D / (ΔIL · fsw) = (12 − 5) · 0,417 / (0,60 · 200 kHz) 24,3 µH
Minimum capacitance (ΔV = 50 mV) C ≥ ΔIL / (8 · fsw · ΔV) = 0,60 / (8 · 200 kHz · 0,05 V) 7,5 µF
Peak inductor current Ipico = Iout + ΔIL / 2 = 2 + 0,30 2,30 A
Minimum MOSFET voltage (20 % margin) VDS ≥ 1,2 · Vin = 1,2 · 12 V 14,4 V

In the report, every line shows the formula, the substituted values and the component chosen to meet that requirement.

A report for every circuit

Everything needed to review, manufacture and maintain the circuit

  • Project requirements and specifications
  • Step-by-step calculation record
  • Every component choice justified by the calculation
  • Bill of materials (BOM) with designators and manufacturers
  • The datasheet of every chosen component
  • SPICE simulation results and ERC/DRC checks
  • Final verdict: proof that the circuit works

As a PDF, in three levels — simple, detailed or complete — for management, the technical team or certification.

Before manufacturing

Checks that usually only happen after the first prototype

Tolerances and yield (Monte Carlo)

Hundreds of simulations with real component tolerances show how many boards will meet the specification before you order them.

Power-stage parasitics

Capacitor ESR and ESL, inductor resistance, traces and switching-loop inductance go into the simulation — not left for the bench.

Thermal and design for manufacturing (DFM)

Junction temperature of every component from the real losses, with a warning for those over the limit, plus a check of the board manufacturing rules.

Supply-chain risk

Every BOM component is checked: obsolescence (EOL, NRND), single source, low stock and alternatives — with cost per distributor.

Validated reference designs

We start from manufacturers validated reference designs, with every component identified by part number, manufacturer and footprint.

Smart datasheet reading

Datasheet tables and graphs are read by computer vision, even in difficult layouts — the parameters go straight into the calculations.

A complete team

More than 90 specialist agents review every decision

Engineers, technicians and project managers working together on every project — always available and always learning.

Engineers

Specialists in power, analog, digital, RF, magnetics, thermal, EMI and PCB: they calculate, choose components, design and justify every decision.

Technicians

On the bench with LabVIEW and NI PXIe: they set up the tests, acquire the signals, measure, diagnose faults and record the real results.

Project managers

They plan the stages, assign the work to the specialists, track deadlines and quality and make sure nothing moves forward unvalidated.

Power electronics

16 topologies — buck, boost, buck-boost, SEPIC, Ćuk, Zeta, flyback, forward, half and full bridge, push-pull, rectifiers, resonant and inverters — with magnetics, MOSFETs, losses, PWM, thermal and EMI.

Analog

Amplifiers, filters and buffers, impedance and current/voltage conversion, oscillators and waveform generators.

Digital & high speed

High-speed channels (PCIe, USB, HDMI), memory interfaces (DDR, SRAM, Flash) and 24 protocol families — I2C, SPI, CAN, RS-485, Modbus, EtherCAT, LoRa, Zigbee…

PCB & manufacturing

Layout in Altium Designer with power, impedance and stack-up rules, DRC, Gerbers, BOM and Pick&Place ready for the factory.

Document reading

Reads datasheets, schematics and application notes and turns them into technical parameters you can use in the design.

Validation & explanation

Compares the result with the specifications, explains every decision in plain or technical language and flags what needs attention.

Sourcing & cost

BOM optimisation, cost per distributor and alerts for obsolescence and single sourcing before you buy.

Bench & instrumentation

Connection to LabVIEW, NI PXIe and MATLAB/Simulink for tests with real hardware (hardware-in-the-loop).

What you gain

Less risk, more capacity, nothing lost

Fewer prototype respins

Errors are caught in calculation and simulation, not on the bench.

Auditable decisions

Every choice has a reason, a calculation and a document — useful for reviews and certification.

New engineers productive sooner

The team's experience is available from day one.

Manufacturing without surprises

A complete, verified manufacturing pack, ready for any PCB factory.

Want your next circuit to come out fully documented?

Tell us what you need. We reply within 1 working day with the next steps.